JASMA, Con Rod (H-Beam) – Honda B18C – SKU : 31053
– Comes with 4 pieces 8740 bolts Rods Features : – Material : Precision forged 4340 EN24 aircraft chrome moly quality steel. – Hardness after quenching and tempering is HRC35-38. – 3D design offers the advantages of reduced weight without sacrificing strength. – 2 pieces forging for increased strength. – Silicon bronze bushings for floating piston pins. – Each forging is X-rayed, sonic tested and magnafluxed. – Special Dowelled Cap for precision alignment. – Shot peened to relieve stress. – Fully CNC machined on all surfaces to produce the lightest and strongest rod. – Forged Billet 4340 aircraft quality steel
Machining Tolerances : – Big End and Small End Tolerance: <= +/-0.00017″ – Verticality, Parallelism and Distortion: <= +/-0.00018″ – Center to Center Distance Tolerance: <= +/-0.001″ – Sets weight matched to +/-1 gram.
Item Description : – BLOX Racing Individual Throttle Bodies(ITB)Manifold. – Color : Silver With Blue Rail. – ITB Inlets Are CNC Machined From Billet Aluminum Solid Piece. – Each Intake Runner Is Made Same Length. – ITB Improves Response Of Your Engine,Gain Additional HP With Proper Tuning. – Individual Throttle Bodies Allow The Engine To Operate More Efficiently By Decreasing Pumping Losses To Achieve More Horsepower. – Engine Will Rev Up Much Faster To Get Desire Power Band. – Design And Quality Of BLOX USA. – Disclaimer: This System Require Proper Engine Management And Tuning For Maximum Performance,Will Not Work With Factory Computers. – Product Description:BLOX individual throttle body kits improve engine response and power output, through the use of one throttle body per cylinder. Effective tuning per cylinder not compromised tuning with only one throttle body.
Qualities : – Reduce air volume within the manifold and improve acceleration response – Super response – The improvement of the accelerator response is due to the reduction in volume of air within the manifold – Straight induction ports – Each intake is made the same length – Increased power – Improved induction efficiency gives the engine the correct quantities of air/fuel on demand. – ITB inlet are CNC machined from billet aluminum solid piece – Airflow bench tested trumpet – Bottom & mid range Torque increase – Each cylinder receives a fuller charge of air/fuel especially at low to mid engine speeds. This is due to the independent throttle bodies and more effective injector positioning – Design and Quality of BLOX U.S.A
Golden Eagle intake gaskets will help reduce intake air temps by removing the direct connection of the intake manifold to the cylinder head. By placing this thermal gasket between the intake manifold and the cylinder head, you will help reduce the amount of heat soak the intake manifold normally absorbs from the cylinder head.
– Thermal Shield Gaskets will reduce heat soak between your intake manifold and your head.
– Made from virgin sheet material with high heat deflection.
– Max operating temperature 500°F/260°C
Advantages to this System are :
– Reduces Heat soak / transfer from the engine into the intake manifold where a Manifold Divider Gasket is used
– Throttle body spacers achieve the same result where most throttle bodies utilize hot water chokes and emission controls.
– The cooler manifold no longer heats the incoming air which allows increased ignition timing / tuning
– This modification can be installed without visible signs and can retain factory new vehicle warranties.
– Can be cleaned and refitted multiple times
– This is considered to be an extension of any Cold Air Induction kit fitted to your vehicle. Why pump cold air in only to be heated by the manifold.
Why do they Work :
– For every 5 Degree reduction in temperature, increases the density of the air and therefore the power by 1%
– The cooler the air, the more dense it is with a greater proportion of oxygen molecules.
– The more air your engine can ingest when it is cooler and denser, the more air to be mixed with fuel providing greater thermal efficiency
– With the appropriate tuning, providing more power, fuel economy and most importantly, more reliability.
GOLDEN EAGLE, Intake Manifold Gasket – Honda
– Material : Teflon
– Thickness : 3mm
